SikaShield® P44 PE Defend RT 4 mm
(Formerly Index Defend Anti Root )
SikaShield® P44 PE Defend RT 4 mm is an APP modified bituminous waterproofing membrane with a thickness of 4 mm. It contains an anti-root additive, which allows the membrane to be in direct contact with the soil. It is reinforced with a non-woven polyester fabric dimensionally stabilised with glass fibre and is flexible at -10 °C. The underside of the product has a burn-off film for easy torch-application.
- Good resistance to root penetration
- Can be applied in direct contact with soil
- Good resistance to humic acids and fertilizers
- Resistant to aggressive mediums in natural ground water and soil
- Good durability
- Fully bonded
- Easy to install by torching method
- Good mechanical properties (tensile, tear, shear)
Usage
The Product is used as a waterproofing membrane for:- Balconies and terraces under a heavy protection layer such as tiles or gravel.
- Flat and sloped roofs under protective layers or ballast
- Roof gardens
- Roof garden with final waterproofing layer in contact with soil
- Car park decks
- Wet areas
- Basements and other below ground structures
- Horizontal reinforced concrete slabs, decks and podiums
- Vertical reinforced concrete walls
- Base sheet in multi-layer systems
- The Product is not suitable for roofs permanently exposed to UV radiation.
Advantages
- Good resistance to root penetration
- Can be applied in direct contact with soil
- Good resistance to humic acids and fertilizers
- Resistant to aggressive mediums in natural ground water and soil
- Good durability
- Fully bonded
- Easy to install by torching method
- Good mechanical properties (tensile, tear, shear)
Packaging
Roll width | 1.0 m |
Roll length | 10.0 m |
Refer to the current price list for available packaging variations.
Colour
Top surface | Polyethylene film |
Bottom surface | Polyethylene film |
Product Details
APPROVALS / CERTIFICATES
-
CE marking and declaration of performance based on EN 13707:2004+A2:2009 Flexible sheets for waterproofing — Reinforced bitumen sheets for roof waterproofing
-
CE marking and declaration of performance based on EN 13969:2004/A1:2006 Flexible sheets for waterproofing — Bitumen damp proof sheets including bitumen basement tanking sheets
-
Resistance to root damage FLL, Hochschule Geisenheim University
Composition
Composition | APP modified bitumen with anti-root additive |
Reinforcing material | non-woven polyester fabric dimensionally stabilised with glass fibre |
Shelf life
36 months from date of production
Storage conditions
The Product must be stored in original unopened and undamaged packaging in dry conditions and temperatures between +5 °C and +35 °C. Protect the Product from direct weather exposure and sunlight. Store in a vertical position. Pallets may be stacked on top of the rolls if all following conditions are met:
The rolls have a wooden board on top, separating them from the pallet above.
The weight of the pallet above is equal to or less than the weight of the rolls.
Always refer to packaging.
Effective thickness
Effective thickness | 4.0 mm ± 0.2 mm |
Resistance to tear
Longitudinal (MD) | 140 N ± 42 N |
Transversal (CMD) | 140 N ± 42 N |
Joint shear resistance
Longitudinal | 350 N/50 mm ± 70 N/50 mm |
Transversal | 250 N/50 mm ± 50 N/50 mm |
Flexibility at low temperature
≤ -10 °C | (EN 1109) |
Watertightness
Method B: 24 hours at 60 kPa | Pass |
Reaction to fire
Class E | (EN 13501-1) |
Application
Ambient air temperature
Minimum | +5 °C |
Maximum | +40 °C |
Relative air humidity
Maximum | 80 % |
Substrate temperature
Maximum | +40 °C |
Minimum | +5 °C |
SUBSTRATE QUALITY
SYSTEM DESIGN
Consider the following when designing the system:
The supporting structure must be of sufficient structural strength to support all new and existing layers of the system build-up.
If used as a roof system, the complete system must be designed to withstand and be secured against wind uplift loadings.
SUBSTRATE CONDITION
The substrate surface must be uniform, firm, smooth and free of any sharp protrusion or burrs, clean, dry, free of grease, laitance, oil, dust and loosely adhering particles.
SUBSTRATE PREPARATION
PRIMING
1.Apply Sika® Igolflex P-10+ primer at a rate of 6-8m2 per litre. Note: Consumption rates will vary depending onsubstrate type and porosity.
2. Allow the primer to dry before membrane installation
APPLICATION
IMPORTANT
Unrolling at low temperatures
At low temperatures, the membrane becomes less flexible.
- Be careful when unrolling to avoid damaging the membrane.
IMPORTANT
Damage through footwear
Footwear with spikes or sharp protrusions may puncture the membrane.
- Use footwear with a flat profile when walking over the membrane.
IMPORTANT
Damage through overheating
The polyester melts at +260 °C. If it is damaged through overheating, the membrane becomes unusable.
- Keep moving the flame while torching to avoid overheating the membrane.
IMPORTANT
Reduced adhesion through insufficient heating
Make sure to heat the membrane sufficiently. If it is not sufficiently heated, the adhesion to the substrate, between layers or on the overlaps will be reduced.
- If the membrane does not adhere to other elements, lift and retorch the unbonded areas.
IMPORTANT
Application at less than +5 °C
When applying the membranes at temperatures lower than +5 °C, use heating equipment to ensure that the substrate temperature is within the given temperature range.
IMPORTANT
Application on sloped surfaces
For slopes with an inclination greater than 15 %, multi-layered roofs must be carefully designed and, if necessary, integrated with mechanical fastenings.
Seasonal symbol
Note: If a seasonal symbol is printed on the roll’s label, it is advisable to use the membrane during the indicated season.
Tackiness at high temperatures
Note: When laying the membrane at high temperatures, the integral adhesive will become 'tacky' and may restrict laying operations.
ALIGNMENT
IMPORTANT
Avoid coinciding joints
To avoid coinciding joints, lay the membranes parallel to one another. When applying on another bituminous membrane, make sure to straddle the overlaps of the previous layer.
- Unroll the membrane.
- Align the membrane.
- Re-roll the membrane before application.
MEMBRANE OVERLAPS
- Overlap the membranes by a minimum of 100 mm on the sides and 150 mm on each end or as specified by the supplier.
- At the end overlap, cut off a corner measuring 100 mm per side at an angle of 45°.
TORCHING
- Heat the substrate and the backing film on the underside of the membrane with a gas burner.
- When the backing film starts to melt, the membrane is ready to stick.
- Roll the heated membrane forward and press it firmly against the substrate to bond it.
- Make sure a bead of melted bitumen is visible along the full length of the overlap sides and ends when laying.
Suitable substrates for torching
-
Concrete
-
Perlite screed
-
Bituminous membranes with a smooth surface
-
Coatings (check the compatibility)
-
Brick masonry
-
Cementitious screeds
DETAILING
- Use a sharp knife to cut in all details such as internal and external corners, upstands, vent pipes, drains, support metalwork etc.
Refer to the relevant method statement for further information on detailing.