Sikafloor®-324
Sikafloor®-324 is a two part solvent free, pigmented with FP3 epoxy paste, self smoothing polyurethane resin, with tough-elastic properties. Sikafloor®-324 makes use of Sika's unique i-Cure technology to improve surface aesthetics and reduce sensitivity for ambient humidity during application.
- Flexible and tough-elastic
- i-Cure based chemistry
- Crack-bridging
- Application on asphalt substrates possible (mastic asphalt)
- Good chemical and mechanical resistance
- Solvent-free and low VOC emissions
- Possible slip resistant surface
- Easy to apply and to keep clean
- Economical
- Not sensitive to moisture
Usage
- Car Park decks and ramps
- Smooth wearing course with crack-bridging properties for industrial floors in production and storage facilities, work shops etc.
- Broadcast wearing course with crack-bridging properties for wet working areas (food and beverage industry etc.),
- Applicable on asphalt surfaces
- Indoor areas, as in shopping centers, exhibition and storage areas.
Advantages
- Flexible and tough-elastic
- i-Cure based chemistry
- Crack-bridging
- Application on asphalt substrates possible (mastic asphalt)
- Good chemical and mechanical resistance
- Solvent-free and low VOC emissions
- Possible slip resistant surface
- Easy to apply and to keep clean
- Economical
- Not sensitive to moisture
Packaging
Part A | 20.25 kg containers |
Part B | 4.75 kg containers |
Part A+B | 25.0 kg ready to mix units |
Colour
Part A | coloured, liquid |
Part B | brownish, liquid |
Sikafloor®-324 is available in broad range of colours.
Product Details
APPROVALS / CERTIFICATES
- Synthetic resin screed material according to EN 13813:2002, certified by Factory Production Control Body and provided with the CE-marking
- Coating for concrete protection according to EN 1504-2:2004, certified by Factory Production Control Body and provided with the CE-marking
- Fire classification according to DIN EN 13501-1:2010-01: Report No. 20150909/01, MPA Dresden
- Paint compatibility according to PV 3.10.7 tested at HQM Induserv Germany, test report 15-08-15203573-001.
- Crack bridging properties following to EN 1062-7 method A, Test report No: 51-15-0056, IBOS GmbH.
- Slip resistance class determined according to DIN 51131, test reports 020109-15-16, 020109-15-16a, 020109-15-17, 020109-15-17a, 020109-15-18, 020109-15-18a
Composition
Polyurethane (PUR)
Shelf life
12 months from date of production
Storage conditions
The packaging must be stored properly in original, unopened and undamaged sealed packaging, in dry conditions at temperatures between +5 °C and +30 °C.
Density
| Part A | ~1.4 kg/l |
| Part B | ~1.2 kg/l |
| Mixed resin (filled 1:0.5) | ~1.6 kg/l |
Filling 1:0.5 with quartz sand F34 0.1–0.3 mm. All Density values at +23 °C.
Solid content by mass
~100 %
Solid content by volume
~100 %
Shore D Hardness
~ 60 (7 days/23 °C/50 % r.h.) | (DIN 53505) |
Abrasion resistance
| ~ 65 mg (14 days/23 °C/50 % r.h.) | (ASTM D 4060) |
Tensile strength
~ 14 N/mm2 (14 days/23 °C/50 % r.h.) | (DIN EN ISO 527-2) |
Tensile adhesion strength
| >1.5 N/mm2 (failure in concrete) | (EN 13892-8) |
Chemical resistance
Resistant to many chemicals. Contact Sika technical service for specific information.
Application
Mixing ratio
Part A : Part B = 81 : 19 (by weight)
Ambient air temperature
+10 °C min. / +30 °C max.
Relative air humidity
~ 75–80 %
Dew point
Beware of condensation!
The substrate and uncured floor must be at least 3 °C above dew point to reduce the risk of condensation or blooming on the floor finish.
Substrate temperature
+10 °C min. / +30 °C max.
Substrate moisture content
< 4 % pbw moisture content. Test method: Sika®-Tramex meter, CM - measurement or Oven-dry-method.No rising moisture according to ASTM (Polyethylene-sheet).
Pot Life
Temperatures | Time |
+10°C | ~ 40 minutes |
| +20°C | ~ 30 minutes |
+30°C | ~ 20 minutes |
Curing time
Before overcoating Sikafloor®-324 allow:
Substrate temperature | Minimum | Maximum |
+10°C | ~ 30 hours | ~ 72 hours |
| +20°C | ~ 24 hours | ~ 48 hours |
+30°C | ~ 16 hours | ~ 36 hours |
Applied product ready for use
Temperature | Foot traffic | Light traffic | Full Cure |
+10°C | 1 day | 3 days | 9 days |
| +20°C | 12 hours | 2 days | 5 days |
+30°C | 8 hours | 1 day | 3 days |
Note: Times are approximate and will be affected by changing ambient conditions
Consumption
Please refer to the System Data Sheets
MIXING
Prior to mixing, stir part A mechanically. When all of part B has been added to part A mix continuously for 2 minutes until a uniform mix has been achieved. When parts A and B have been mixed, add the quartz sand F34 0.1–0.3 mm and mix for a further 2 minutes until a uniform mix has been achieved. To ensure thorough mixing pour the materials into another pail and mix
again to achieve a consistent mix. After mixing leave the mixture for 3 minutes to react before applying.
Mixing Tools
Sikafloor®-324 must be thoroughly mixed using a low speed electric stirrer (300 - 400 rpm) or other suitable equipment.
APPLICATION
Prior to application, confirm substrate moisture content, relative humidity and dew point.
Sikafloor®-324 is poured and spread evenly by means of a serrated trowel or pin rake. When used in a selfsmoothing system, roll in two directions with a spike roller to ensure even thickness and to remove entrapped air.
CLEANING OF EQUIPMENT
Clean all tools and application equipment with Thinner C immediately after use. Hardened and/or cured material can only be removed mechanically.
CLEANING
To maintain the appearance of the floor after application, Sikafloor®-324 must have all spillages removed immediately and be regularly cleaned using rotary brush, mechanical scrubbers, scrubber dryer, high pressure washer, wash and vacuum techniques etc., using suitable detergents and waxes.