Sikafloor® MultiDur ES-24
Sikafloor® MultiDur ES-24 is a smooth or finely textured pigmented 2-3 mm floor.
- Good chemical and mechanical resistance
- High wear resistance
- Gloss finish
- Textured - fine finish - easily cleaned
- UV Stable (with top coat Sikafloor 359)
System Structure
Usage
- Maintenance workshop service areas
- Education - trade work areas
- Food and Beverage Facilities - mainly dry packaging areas
- Manufacturing facilities - Printing, Processing
- Cleanroom Parmaceutical
Advantages
- Good chemical and mechanical resistance
- High wear resistance
- Gloss finish
- Textured - fine finish - easily cleaned
- UV Stable (with top coat Sikafloor 359)
Colour
Available colours in RAL Range on request.
Standard Colours : Light Grey 7035, Pebble Grey 7032, Koala Grey N45, Window Grey 7040, Dusty Grey 7037, Oxide Red 3009, Sky Blue 5015, Dahlia Yellow 1033.
Appearance
Smooth gloss finish or fine non slip texture
System Details
APPROVALS / CERTIFICATES
- Texture - conforms to AS 4586 -2013 P ratings
- VOC Australian Standards ASTM D3960 - Green Star Building Council - V2 IEQ-13 V1 IEQ-1
- APAS Certification 0209/1L (Sikafloor 160/264T)
- Fire - Critical Radient Flux - Pass AS/ISO 9239-1:2003
- Particle emission certificate Sikafloor-263 SL CSM Statement of Qualification – ISO 14644-1, class 5– Report No. SI 0904-480 and GMP class A, Report No. SI 1008-533.
- Outgassing emission certificate Sikafloor-263 SL CSM Statement of Qualification – ISO 14644-8, class 6,5 - Report No. SI 0904-480.
- Good biological Resistance in accordance with ISO 846, CSM Report No. 1008-533
- Fire classification in accordance with EN 13501-1, Report-No. 2007-B-0181/14, MPA Dresden, Germany, February 2007
System structure
| 1. Primer | Sikafloor®-161/-160 |
| 2. Wearing Coat 3. Finish texture coat- Optional 4. Optional: UV Stable Top Coat | Sikafloor®-263 SL Sikafloor 264/264T AU Sikafloor 359 |
Composition
Epoxy
Nominal thickness
~2.0 – 3.0 mm
Shore D Hardness
| ~76 (7 days / +23 °C) | (DIN 53 505) |
Abrasion resistance
| ~35 mg (CS 10/1000/1000) (7 days / +23 °C) | (DIN 53 109 Taber Abraser Test) |
Resistance to impact
| ~10 Nm (14 days / +23 °C / 50 %) | (ISO 6272) |
Compressive strength
| ~ 50 N/mm2 ( Resin filled 1:0,9 with F34 at 28 days / +23 °C) | (EN 196-1) |
Tensile strength
| ~ 16 N/mm2 ( Resin filled 1:0,9 with F34 at 28 days / +23 °C) | (EN 196-1) |
Tensile adhesion strength
| > 1.5 N/mm² (failure in concrete) | (ISO 4624) |
Reaction to fire
| Critical Radiant Flux - Pass | AS/ISO 9239.1 AP VS0209 Appendix B |
Chemical resistance
Resistant to many chemicals. Contact Sika technical service for specific advice.
Temperature resistance
| Exposure* | Dry heat |
| Permanent | +50 °C |
| Short-term max. 7 d | +80 °C |
| Short-term max. 12 h | +100 °C |
Short-term moist/wet heat* up to +80 °C where exposure is only occasional (steam cleaning etc.).
*No simultaneous chemical and mechanical exposure.
Application
Material temperature
Please refer to the individual Product Data Sheet
Ambient air temperature
+10 °C min. / +30 °C max.
Relative air humidity
80 % r.h. max.
Dew point
Beware of condensation!
The substrate and uncured floor must be at least 3 °C above dew point to reduce the risk of condensation or blooming on the floor finish.
Substrate temperature
+10 °C min. / +30 °C max.
Substrate moisture content
When performing application work with Sikafloor® MultiDur ES-24, the substrate moisture content must not exceed 4 % pbw measured by Tramex.
Test method: Sika®-Tramex meter, CM - measurement or Oven-dry-method.
No rising moisture according to ASTM (Polyethylene-sheet).
Use Sikafloor 161 Primer for moisture to 6%pbw.
For >6%pbw use Sikafloor EpoCem 81.
Waiting time to overcoating
Before applying Sikafloor®-263 SL on Sikafloor®-156/-161/-160 allow:
| Substrate Temperature | Minimum | Maximum |
| +10 °C | 24 hours | 3 days |
| +20 °C | 12 hours | 2 days |
| +30 °C | 8 hours | 1 day |
Applied product ready for use
| Temperature | Foot Traffic | Light Traffic | Full Cure |
| +10 °C | ~72 hours | ~6 days | ~10 days |
| +20 °C | ~24 hours | ~4 days | ~7 days |
| +30 °C | ~18 hours | ~2 days | ~5 days |
Consumption
| Coating System | Product | Consumption |
| Primer Scratch coat (If required) | 1 × Sikafloor®-160/-161 Sikafloor®-161 filled 1:0.5 filler 503 | ~ 0.25–0.35 kg/m²
1 kg/m² |
| Wearing coat | 1 x Sikafloor®-263 SL 2 and 3mm comprising of 1kg of Sikafloor®-264 and 1kg of filler 503 | ~ 1.9kg/m²/mm |
| Finish coat - optional | Sikafloor 264/-264T AU | ~ 0.20–0.30 kg/m² |
| UV stable Topcoat | Sikafloor 359 AU | 6-8 m²/litre |
Note: For addtional texture, incorporate 60 mesh size alumimium oxide at 5-6% by vol. into finish coat.
SUBSTRATE QUALITY
Substrate be free of contaminants.
Refer to individual Sikafloor 161/263SL and 264T AU TDS.
25Mpa - Cohesive bond pull off value of >1.5 mpa.
Note; Bond tests should be conducted to confirm the suitability of the substrate.
SUBSTRATE PREPARATION
Surfaces should be clean, dry and free of contaminants.
Prepared surface should produce a cohesive bond pull off value of min.1.5Mpa. and a moisture level of <4%pbw.
All unsound layers of laitance and any existing coatings are to be removed.
Self smoothing layers of Sikafloor® MultiDur ES-24 will not re profile irregularities in the concrete surface.
Profile and defects greater than approx.1.5-2mm will require re-levelling.
This can be achieved using Sikafloor 160/161 mortars and or scratch filling layers.
For application of Sikafloor® MultiDur ES-24 over existing resin finishes, refer to Sika Technical Dept. for direction.
MIXING
Refer to individual Sikafloor 160/161/263SL and 264T AU TDS
APPLICATION
Refer to individual Sikafloor 160/161/263SL and 264T AU TDS
CLEANING
Refer to the Method Statement Sikafloor®‐ Cleaning Regime