Sikafloor® MultiDur EB-14
High build Broadcast textured non slip pigmented epoxy floor coating
Sikafloor® MultiDur EB-14 is a textured, multi-purpose high build floor coating system. It is an economical option for a range of Commercial and Industrial applications where slip resistance is important, particularly wet areas.
- Textured finish P3 to P5
- Good chemical and mechanical resistance
- Pigmented - range of colours
- Easy application
- Economical
- Gloss finish
System Structure
Usage
- Automotive washbays
- Food and Beveridge processing- wet, light to medium duty
- Bars - servery areas
- Back-of-house Commercial
- Car Parks - wet zones and ramp ways
Advantages
- Textured finish P3 to P5
- Good chemical and mechanical resistance
- Pigmented - range of colours
- Easy application
- Economical
- Gloss finish
Colour
Available in colours of RAL range on request.
Standard Colours : Light Grey 7035, Pebble Grey 7032, Koala Grey, N45, Window Grey 7040, Dusty Grey 7037, Oxide Red 3009, Sky Blue 5015, Dahlia Yellow 1033.
Appearance
Slip resistant, gloss finish
System Details
APPROVALS / CERTIFICATES
- VOC compliance as per Auatralian Standards Test ASTM D3960 GreenStar V2 IEQ-13 and V1 IEQ-11
- Slip resistance - Textures comply with Australian Standards P Ratings AS 4586-2013
- Slip resistance certificate according to DIN 51130, class R11 V4, Report No.020108-13-16, Roxeler Institute, October 2013, Germany
- Slip resistance certificate according to DIN 51130, class R12 V6, Report No.020108-13-18, Roxeler Institute, October 2013, Germany
- Certified as Surface Protection System OS 8 according to DIN EN 1504-2 and DIN V 18026.
- Fire - Critial Radiant Flux - Pass AS/ISO 9239.1 AP VS0209 Appendix B
- APAS Certification APAS 0209/1(Sikafloor 160)
System structure
Sikafloor® MultiDur EB-14 system (~ 1.5-2mm)
| 1. Scratch coat & broadcast | Sikafloor®-161/-160 & broadcast with quartz sand 0.4–0.7 mm |
| 2. Wearing coats | Sikafloor®-264 x 2 |
Composition
Epoxy
Nominal thickness
~1.5–2mm
Chemical resistance
Please refer to the chemical resistance chart of Sikafloor®- 264
Temperature resistance
| Exposure* | Dry heat |
| Permanent | +50 °C |
| Short-term max. 7 d | +80 °C |
| Short-term max. 12 h | +100 °C |
Short-term moist/wet heat* up to +80 °C where exposure is only occasional (i.e. during steam cleaning etc.)
*No simultaneous chemical and mechanical exposure.
Skid / slip resistance
| P3 30/60 Broadcast Agg. | AS 4586-2013 |
| P4 - 5 18/40 Brodacast Agg. | AS 4586-2013 |
Application
Material temperature
Please refer to the individual Product Data Sheet
Ambient air temperature
+10 °C min. / +30 °C max.
Relative air humidity
80 % r.h. max.
Dew point
Beware of condensation!
The substrate and uncured floor must be at least 3 °C above dew point to reduce the risk of condensation or blooming on the floor finish.
Substrate temperature
+10 °C min. / +30 °C max.
Substrate moisture content
When performing application work with Sikafloor® MultiDur EB-14, the substrate moisture content must not exceed 4 % pbw measured by Tramex.
Test method: Sika®-Tramex meter, CM - measurement or Oven-dry-method.
No rising moisture according to ASTM (Polyethylene-sheet).
Use Sikafloor 161 Primer for moisture to 6%pbw.
For >6%pbw use EpoCem 81.
Waiting time to overcoating
Before applying Sikafloor®-264 on Sikafloor®-156/-161/-160 allow:
| Substrate temperature | Minimum | Maximum |
| +10 °C | 24 hours | 3 days |
| +20 °C | 12 hours | 2 days |
| +30 °C | 8 hours | 1 day |
Before applying Sikafloor®-264 on Sikafloor®-264 allow:
| Title 1Substrate temperature | Minimum | Maximum |
| +10 °C | 30 hours | 48 hours |
| +20 °C | 24 hours | 24 hours |
| +30 °C | 16 hours | 30 hours |
Times are approximate and will be affected by changing ambient conditions particularly temperature and relative humidity
Applied product ready for use
| Temperature | Foot traffic | Light traffic | Full cure |
| +10 °C | ~ 72 hours | ~ 6 days | ~ 10 days |
| +20 °C | ~ 24 hours | ~ 4 days | ~ 7 days |
| +30 °C | ~ 18 hours | ~ 2 days | ~ 5 days |
Consumption
Sikafloor® MultiDur EB-14 system (~ 2–3 mm)
| Coating System | Product | Consumption |
| Primer Scratch Coat (If required) | 1 × Sikafloor®-160/-161 Sikafloor®-161 filled 1:0.5 filler 503 | ~0.25-0.35 kg/m² 1 kg/m² |
| Broadcast in excess | quartz sand 0.4–0.7 mm | ~3-4 kg/m² |
| First seal coat | 1 × Sikafloor®-264 | ~0.55–0.65 kg/m² (2.2-2.5m²/litre) |
| Second seal coat | 1 × Sikafloor®-264 | ~0.25–0.30 kg/m² (4.7-5.5m²/litre) |
CLEANING
Please refer to the Method Statement Sikafloor®‐ Cleaning Regime