Sikafloor®-264 T AU
Textured High Build Durable 100% Solids Pigmented Non Blooming Epoxy Coating
Sikafloor®-264 T AU is a thixotropic, textured 2- componant solvent free pigmented 100% solids high build epoxy coating for durable, decorative finishes. It can be appied to vertical surfaces in addition to providing durable floor surface.
- Tough / Durable
- Very good abrasion resistance
- Excellent resistance to whiteneing / blooming from early exposure to surface moisture
- Textured non-slip surface
- Can be applied on vertical and horizontal surfaces
- Easily cleaned and maintained
- Very good chemical resistance (Refer to Sika Chem. resistance data)
Usage
Sikafloor®-264 T AU can be used in a variety of Industrial and commercial applications;- Automotive workshops
- Food related premises
- Clean rooms- Laboratories
- Pharamaceutical
- Stadiums
- Correctional facilities
- Amenities / Washrooms
- General accessways/ Back of house
Advantages
- Tough / Durable
- Very good abrasion resistance
- Excellent resistance to whiteneing / blooming from early exposure to surface moisture
- Textured non-slip surface
- Can be applied on vertical and horizontal surfaces
- Easily cleaned and maintained
- Very good chemical resistance (Refer to Sika Chem. resistance data)
Packaging
| Part A | 6.55 kg |
| Part B | 2.0 kg |
| Sikafloor Pigment 1.15 kg | 1 x 1.15 kg |
| Part A+B+Pigment | 9.7 kg ready to mix kits (7.3 L) |
| Part A | 13.09 kg |
| Part B | 4.0 kg |
| Sikafloor Pigment 1.15 kg | 2 x 1.15 kg |
| Part A+B+Pigment | 19.39 kg ready to mix kits (14.6 L) |
| Part A | 15.39 kg |
| Part B | 4.0 kg |
| *Pre-pigmented kits | 19.39 kg ready tomix kits (14.9 L) |
Colour
| Resin - part A | coloured, liquid |
| Hardener - part B | transparent, liquid |
| Extended colour range |
Colours:
Sikafloor®-264 T AU system is available in a range of standard RAL colours
- Non standard colours can be supplied on request.
- Refer to the Sikafloor epoxy colour chart for details
*Pre-pigmented kits are available in 4 colours: RAL 7035 Light Grey, RAL 7040 Window Grey, RAL 7037 Dusty Grey & N45 Koala Grey
Note: Lighter colours may require more pigment than the standard dose of 1.15kg. Priming with an addition of white pigment to assist coverage for lighter colours is recommended. Refer to Sika Technical Dept. for more details
Product Details
Shelf life
12 months
Storage conditions
Store away from direct sunlight and idealy between +5 to 35 Degrees C
Density
Part A - 1.41kg/litre Part B - 1.00kg/litre Pigment - 1.75kg/litre Resin mixed - 1.33kg/litre all density values at +23 degrees C
Volatile organic compound (VOC) content
Conforms to Aust.Standard test ASTM D3960.
Greenstar Building Council of Australia - Green Star Office Design V2 IEQ-13 / Green Star Office Interiors V1.1 IEQ-11
Shore D Hardness
76 (7 days / +23 degrees C)
Abrasion resistance
70mg (CS10/1000/1000) (8 days / +23 Degrees C) DIN. 53 109 Taber Abrader test
Gloss level
Low sheen to Semi gloss (depending on temperature at application)
Chemical resistance
Sikafloor®-264 T AU has excellent resistance to a wide range of chemicals. Refer to Sika Technical for specific information on resistance to chemicals.
Application
Layer thickness
Approx. total system DFT 0.6- 0.7mm (Depending on substrate density and profile)
Ambient air temperature
+10 degreesC min. / +30 degreesC max.
Relative air humidity
80% r.h max.
Dew point
Beware of condensation The subsrate and uncured floor must be at least 3 degrees C above dew point to reduce the risk of condensation or blooming of the surface finish.
Substrate temperature
+10 degrees min. / +30 degrees min.
Pot Life
Approx. values +10 degrees C approx 25 min. +20 degrees C 15 min. +30 degrees C 8 min
Waiting time to overcoating
Intercoat times between system layers
Substrate Temperature Minimum Maximum
+10 degrees C 24 hours 4 days
+20 degrees C 12 hours 2 days
+30 degrees C 6 hours 1 day
Applied product ready for use
Temperature Foot traffic Light traffic Full cure
+10 degrees C 72 hours 6 days 10 days
+20 degrees C 24 hours 4 days 7 days
+30 degrees C 18 hours 2 days 5 days
Note: These are approximates and will be affected by changing ambient conditions
APPLICATION INSTRUCTIONS
Levelling : Rough surface profiles may need to be levelled first to ensure a high quality even finish. Sikafloor 160 combined with silica fillers. The grade and filler content can be altered to accommodate the depth of profile to be filled. Refer to Sikafloor 160 TDS for guideance.
Mixing: Add pigment pack to the part A and mix to blend in. Add the Part B and mix the full kit for a minimum of 2 minutes.
Application:
Apply product using a medium to long knap roller (15-20mm) with a central pole double frame arrangement. Apply evenly at the prescribed coverage rate then "lay off " in the opposite direction of rolling for optimum results. Final layoff technique - take the weight of the roller and lift the roller from the surface when completing to lay off stroke. Not adopting the technique and or not having sufficient manpower to execute this proceedure will likely result in uneven appearance.
MIXING
Sikafloor®-264 T AU must be thorougly mixed using a low speed stirrer (300 - 400 rpm)
APPLICATION
Placing the kits at an even rate of pot life and joining up wet edges progressively within even time frames is critical for optimum results. If this is not adhered to then differing colour shades will result when the product has reached touch dry stage.
CLEANING OF EQUIPMENT
Clean all tools immediately after use Thinner C. Hardened and/or cured material can only be removed mechanically.
CLEANING
Sikafloor®-264 T AU should be kept as clean as possible to maximise durability and reduce abrasion. Good housekeeping practices should be followed when Chemical spills occur. Clean with neutral based, non solvent based cleaning chemicals. - Refer to Sikafloor Cleaning Guidelines document for more details.