Sika® FloorJoint PS-30 S
Sika® FloorJoint PS-30 S is a carbon fibre reinforced polymer (CFRP) composite, prefabricated, floor joint system with high mechanical resistance for normal up to medium wear loading conditions. Its sinusoidal surface tooth profile allows for an improved load distribution and results in minimum vibrations under direct car and forklift traffic. Gap widths: 0–30 mm.
- Grindable profile for level integration into the floor surface
- Reduced vibrations under direct car and fork lift traffic
- Thermal expansion coefficient similar to resin based floors
- Easy to install / Easy to repair
- Short down time - Trafficable after 24 hours
- Waterproof system design possible
- High chemical resistance
- Non corroding
- High mechanical resistance
Usage
- Floor joint system for new build and refurbished joints in concrete / concrete screeds in:
- Inner zones of car park decks and ramps
Advantages
- Grindable profile for level integration into the floor surface
- Reduced vibrations under direct car and fork lift traffic
- Thermal expansion coefficient similar to resin based floors
- Easy to install / Easy to repair
- Short down time - Trafficable after 24 hours
- Waterproof system design possible
- High chemical resistance
- Non corroding
- High mechanical resistance
Packaging
Refer to individual Product Data Sheet.
System Details
APPROVALS / CERTIFICATES
- Fire Testing DIN EN 13501-1, Sika® FloorJoint, Hoch, Test report No. PB-Hoch-140803-3
- Fire Testing DIN EN ISO 9239-1, Sika® FloorJoint, Hoch, Test report No. PB-Hoch-140802-3
- Fire Testing DIN EN ISO 9239-1, Sika® FloorJoint, Hoch, Test report No. PB-Hoch-140802-3
System structure
Sika® FloorJoint PS-30 S:
| 1. Backing rod | Screed edge stripping. Height: 80 mm–100 mm, thickness 5 mm. |
| 2. Adhesive | Sikadur®-30 or Sikadur®-31 CF Normal |
| 3. Floor joint panel | Sika® FloorJoint S |
| 4. Floor coating | Sikafloor®-304 W/-264 /-263 SL |
Composition
Floor joint panel: Carbon fibre reinforced polymer.
Shelf life
Refer to individual Product Data Sheet.
Storage conditions
Refer to individual Product Data Sheet.
Reaction to fire
| Bfl s1 (composite material of joint panel) | (EN 13301-1) |
Chemical resistance
Resistant to many chemicals. Contact Sika Technical Services for specific information.
Joint design
| Gap widtht1 | Positive joint movement2 | Negative joint movement3 |
| 0 mm | +20 mm 4 | -0 mm |
| 5 mm | +17,5 mm 4 | -5 mm |
| 10 mm | +15 mm 4 | -5 mm |
| 15mm | +12,5mm 4 | -5 mm |
| 20 mm | +10 mm 4 | -5 mm |
| 25 mm | +7,5 mm | -5 mm |
| 30 mm | +5 mm | -5 mm |
- Width of the gap in the concrete below Sika® floor Joint panel during installation.
- Positive joint movement is the amount the gap can open, compared to its original width during installation of Sika® floor Joint panel. Do not exceed the maximum positive joint movement capacity, otherwise the teeth of the Sika® floor Joint panel become unsupported and may be damaged.
- Negative joint movement is the amount the gap can close, compared to its original width during installation of the Sika® floor Joint panel.
- The sealant may break at a positive joint movement of ~10–15 mm, however this does not affect the technical performance of Sika® FloorJoint PS-30 S. The purpose of the joint sealant is the reduction of dirt pick-up in the joint, not to provide water tightness. Install Sikadur® Combiflex® SG System below Sika® FloorJoint PS-30 S if a waterproof joint design is required.
Application
Waiting time to overcoating
Before grinding and applying Sikafloor®-304 W/-263 N SL/-234 N on Sikadur®-30/Sikadur®-31 CF Normal + Sika®-FloorJoint S allow:
| Substrate Temperature | Minimum | Maximm |
| +10 °C | 24 hours | 14 days |
| +20 °C | 12 hours | 10 days |
| +30 °C | 8 hours | 7 days |
Times are approximate and will be affected by changing ambient conditions particularly temperature and relative humidity.
Applied product ready for use
| Temperature | Foot Traffic | Light Traffic | Full Cure |
| +10 °C | 72 hours | 6 days | 10 days |
| +20 °C | 24 hours | 4 days | 7 days |
| +30 °C | 18 hours | 2 days | 5 days |
Times are approximate and will be affected by changing ambient conditions particularly temperature and relative humidity.
Consumption
Sika® FloorJoint PS-30 S System:
| Component | Product | Consumption |
| Adhesive | Sikadur®-30 or Sikadur®-31 CF Normal | ~3–5 kg/linear metre (depending on the depth of the cut-out) |
| Floor joint panel | Sika® FloorJoint S | 1 piece for 1,2 linear metre |
| Floor coating | Sikafloor®-304 W | ~1–2 × 0,13 kg/m² |
These figures are theoretical and do not allow for any additional material due to surface porosity, surface profile, variations in level or wastage etc.
APPLICATION
Refer to the Sika Method Statement: Sika® FloorJoint S.