Sikafloor® MultiDur ES-44 ESD
The Sikafloor® MultiDur ES-44 ESD system is a seamless, smooth, low VOC, ESD epoxy floor covering. It consist out of the two part, self-smoothing, epoxy coating Sikafloor®-263 SL and the two part, water dispersed, coloured ESD polyurethane roller coating Sikafloor®-305 W ESD.
- Very low VOC emissions
- Water based
- Easy to apply
- Easy to refurbish, can be overcoated directly with itself
- Low odour
- Good UV resistance, good resistance to yellowing
- Easy to clean
- Conforms to the requirements of ANSI/ESD S20.20 and IEC 61340-5-1
- Matt surface
- Suitable as floor covering acc. DIN VDE 0100-410 / T610 as top coat of non-conductive Sikafloor products
System Structure
Usage
It is used as:- Dissipative coloured indoor system for electrostatic protected areas (EPA).
- Particularly suitable for areas with requirements for the lowest electrostatic charge (low BVG - Body Voltage Generation) and dissipative surface.
- Typical applications include clean rooms in the Electronics industry, Microbiology/Microchemistry sectors, Data Processing facilities, Production plants in the Automobile industry etc.
Advantages
- Very low VOC emissions
- Water based
- Easy to apply
- Easy to refurbish, can be overcoated directly with itself
- Low odour
- Good UV resistance, good resistance to yellowing
- Easy to clean
- Conforms to the requirements of ANSI/ESD S20.20 and IEC 61340-5-1
- Matt surface
- Suitable as floor covering acc. DIN VDE 0100-410 / T610 as top coat of non-conductive Sikafloor products
Colour
Available in a limited number of colour shades such as RAL 1000, 1001, 1002, 1011, 3012, 5024, 6021, 6024, 7011, 7032, 7035, 7038, 7040, 7042, 7044, 7047, 9018.
Be aware that the colour of the layer below has to be approx. adjusted to the colour of the Sikafloor®-305 W ESD.
Appearance
Smooth - matt surface
System Details
APPROVALS / CERTIFICATES
- Synthetic resin screed material according to EN 13813:2002, Declaration of Performance 02 08 01 02 037 0 000001 2017, certified by notified factory production control certification body 0921, certificate of conformity of the factory production control 2017, and provided with the CE marking.
- Coating for surface protection of concrete according to EN 1504-2:2004, Declaration of Performance 02 08 01 02 037 0 000001 2017, certified by notified factory production control certification body 0921, certificate of conformity of the factory production control 2017, and provided with the CE marking.
- Test of the Insulation Resistance acc. DIN VDE 0100-410/T610. Test Report P 9915-E, Kiwa-Polymer Institut
System structure
Sikafloor® MultiDur ES-44 ESD:
| Primer | Sikafloor®-160/-161 |
| Base coat + Earthing connection | Sikafloor®-263 SL + Sika® Earthing Kit |
| Final conductive coating | Sikafloor®-305 W ESD |
The system configurations as described must be fully complied with and may not be changed.
Composition
Base coat: Epoxy
Top coat: PUR
Nominal thickness
~1.5–2.0 mm
Tensile adhesion strength
> 1.5 N/mm² | (ISO 4624) |
Electrostatic behaviour
Resistance to ground1 | Rg < 109 Ω | (IEC 61340-4-1) |
Typical average resistance to ground2 | Rg < 105 - 106Ω | (DIN EN 1081) |
Body voltage generation2 | < 100 V | (IEC 61340-4-5) |
| System Resistance (Person/Floor/Shoe)3 | < 35 M Ω | (IEC 61340-4-5) |
1 In accordance with IEC 61340-5-1 and ANSI/ESD S20.20.
2 Readings may vary, depending on ambient conditions (i.e. temperature, humidity) and measurement equipment.
3 Or < 109 Ω + body voltage generation of < 100 V, in case of readings > 35 M Ω.
Application
Ambient air temperature
+10 °C min. / +30 °C max.
Relative air humidity
During curing the humidity should not exceed 75 % max. Adequate fresh air ventilation or a dehumidifier must be provided to remove the excess moisture from the curing product.
Dew point
Beware of condensation! The substrate and uncured floor must be at least 3 °C above dew point to reduce the risk of condensation or blooming on the floor finish.
Substrate temperature
+10 °C min. / +30 °C max.
Substrate moisture content
<4 % pbw moisture content.
Test method: Sika Tramex Meter, CM-measurement or Oven-Dry-Method. No rising moisture according to ASTM (Polyethylene-sheet).
Waiting time to overcoating
Before applying Sikafloor®-263 SL on Sikafloor-160/-161 allow:
| Substrate temperature | Minimum | Maximum |
| +10 °C | 24 hours | 4 days |
| +20 °C | 12 hours | 2 days |
| +30 °C | 8 hours | 1 days |
Before applying Sikafloor®-305 W ESD TopCoat on Sikafloor®-263 SL allow:
| Title 1Substrate temperature | Minimum | Maximum |
| +10 °C | 36 hours | 7 days |
| +20 °C | 24 hours | 5 days |
| +30 °C | 16 hours | 3 days |
Before applying Sikafloor®-305 W ESD on Sikafloor®-305 W ESD allow:
| Substrate temperature | Minimum | Maximum |
| +10 °C | 48 hours | 10 days |
| +20 °C | 24 hours | 8 days |
| +30 °C | 16 hours | 7 days |
Times are approximate and will be affected by changing ambient conditions particularly temperature and relative humidity.
Applied product ready for use
| Temperature | Foot traffic | Light traffic | Full cure |
| +10 °C | ~ 48 hours | ~ 5 days | ~ 10 days |
| +20 °C | ~ 24 hours | ~ 3 days | ~ 8 days |
| +30 °C | ~ 16 hours | ~ 2 days | ~ 7 days |
Note: Times are approximate and will be affected by changing ambient conditions
Consumption
Sikafloor® MultiDur ES-44 ESD System
| Coating | Product | Consumption |
| Primer | Sikafloor®-160/-161 | 1–2 × ~ 0.3–0.5 kg/m² |
| Levelling (if required) | Sikafloor®-160/-161 levelling mortar | Refer to PDS of Sikafloor®-160/-161 |
| Base coating | Sikafloor®-263 SL filled with quartz sand F34* | ~1.9–2.7 kg/m² Binder + quartz sand F 34: 1:0.6 – 1:1 pbw (Depending on the air temperature the filling grade varies) |
| Earthing connection | Sika® Earthing Kit | 1 earthing point per approx. 200–300 m², min. 2 per room. |
| Final ESD coating | Sikafloor®-305 W ESD | 1–2 × 0.18–0.2 kg/m²/layer |
CLEANING
Please refer to the Sikafloor® Cleaning Regime.